Team:Cambridge/Modelling

From 2009.igem.org

Revision as of 13:36, 13 August 2009 by MikeDavies (Talk | contribs)


Modelling

Introduction

This project focuses on novel outputs, for example, for environmental sensors. However, there is a need for an 'adaptor'; a middle section to the machine that takes an input and processes it. Our initial work was based around the development of an amplifier that permits a large output that is clearly visible. The next planned stage was the creation of a system that allows switching on of output at different calibrated input signal levels. Creating a model allows the feasibility of the proposed systems to be tested. A basic model of the original amplifier system was put forward, building on both our data and the Cambridge 2007 data.

Modelling the phage activator system

This is the basic 'amplifier' system that consists of an input sensitive promoter system and a protein activator and sensitive promoter. It can therefore be divided into two boxes, the approach taken in putting forward an initial model.

The pBAD promoter

An arabinose input acts as an inducer, permitting transcription, by binding the AraC transcription factor. This is a dual transcription factor; when unbound to arabinose a dimer restricts access of polymersase to reduce basal levels of transcription, upon binding arabinose the conformation changes and the dimer permits binding of polymerase. [1]

To model this situation, araC is first assumed to take the role of a repressor that reversibly binds and unbinds a site on the DNA. If it binds arabinose, it is sequestered and cannot bind the DNA. Here, an input function is created, after Alon []. This gives the rate of transcription from the promoter dependent on the concentration of arabinose. Since mRNA is then translated at a roughly constant rate, it is related with a multiplicative constant to the rate of protein production, in this case activator and RFP.

Cambridge Eq1.gif

This gives the rate of transcription as a function of X* which represents the concentration of active repressor, unbound to arabinose. B is the maximum rate of transcription, here this rate is when induced by arabinose at highest concentration. K_d is the dissociation constant (see modelling derivations). Parameters must be found by a parameter scan for sensible values or by comparing to already gathered data.

The concentration of 'active' repressor is given as a function of arabinose concentration by:

Cambridge Eq2.gif

where X^T is the total amount of araC available, bound or unbound. A is arabinose concentration. n is the number of arabinose molecules binding to each molecule of the repressor, and K is a binding constant. n was taken to be two by assuming that each araC dimer needs two molecules to be bound before it can permit transcription.


Combining these two gives the overall input function, which has leaky transcription included at A = 0, seen in the actual results.

The Activator and its Promoter

This is based on a similar idea. Activator is made by transcription from pBAD, the mRNA is then translated (the potential time delays will be taken into account). The activity of the phage promoter is dependent on activator concentration according to:

Cambridge Eq3.gif

Assuming that translation rates remain constant, the rate of GFP and RFP production would be expected to be multiples of the above promoter activities/ input functions (which represent rate of transcription)

Making a Latch

A switch that remains on once stimulated would be useful if it was only necessary, say, to see if a hazardous contaminant had ever been present in a sample (it could still be there in low levels etc.). A method proposed is positive feedback; an activator placed downstream of its own promoter (as well as the reporter/ pigment) will, in theory, keep pigment production going. The rate of activator production from its own promoter is given in equation 3 above, which is dependent on activator concentration itself.

Modelling the proposed switching levels system

This idea was summarised in the diagram and discussion included in week 4 dry work:Cambridge thresholds.png

Most of these model systems will rely on the very basic equations outlined above, with extensions to add levels of complexity, such as the transport of arabinose into a cell.

Basic Phage Activators

The first step is to take a look at the preliminary data to try to find appropriate parameters. An overall aim for the modelling of this system is to refine the model to each component and attempt to predict how different combinations of components will behave. The data collection separates the promoter and activator by use of both RFP and GFP reporters.

Cambridge Sponsor Logo1.pngCambridge Sponsor Logo2.pngCambridge Sponsor Logo3.pngCambridge Sponsor Logo4.pngCambridge Sponsor Logo5.pngCambridge Sponsor Logo8.pngCambridge Sponsor Logo6.pngCambridge Sponsor Logo7.pngCambridge Sponsor Logo9.pngCambridge Sponsor Logo10.pngCambridge Sponsor Logo11.pngCambridge Sponsor Logo12.pngCambridge Sponsor Logo14.pngCambridge Sponsor Logo13.pngCambridge Sponsor Logo15.pngCambridge Sponsor Logo16.pngCambridge Sponsor Logo17.pngCambridge Sponsor Logo18.pngCambridge Sponsor Logo19.pngBmglab.jpg