Team:Cambridge/Project

From 2009.igem.org

Revision as of 23:44, 21 October 2009 by Vmullin (Talk | contribs)


Project

Introduction

The E. Chromi project strived to facilitate biosensor design and construction. We designed and characterised two types of parts - Sensitivity Tuners and Colour Generators. The availability of these parts on the registry could revolutionize biosensor design in the future - when new promoters that sense novel inputs are characterized and submitted to the registry, Sensitivity Tuners and Colour Generators can be implemented to tune the sensitivity of the promoter to detect a concentration appropriate to the biosensor's desired application, and to report the presence of an inducer in a cheap, user-friendly fashion.

Improving Biosensors

The Parts Registry's repertoire of input-sensitive devices is incredibly varied. Teams have engineered E. coli to be sensitive to a wide range of environmentally significant compounds, including arsenic, mercury, lead, cyanide, etc., to genetically engineer biosensors as an alternative to other technologies. The Cambridge 2009 iGEM team identified two stumbling blocks to biosensor design.

  • Output: Previous iGEM biosensor projects have used pH, electrical conductance, and fluorescence as output. However, these reporter mechanisms require further steps to read the output. While this is acceptable for First World applications, for biosensors to have true Third World applications, a simpler output is necessary.
  • Response to Input: By utilizing an input-sensitive promoter, the biosensor is limited by the sensitivity of the promoter. For example, the promoter might be sensitive to input concentrations which have no real world meaning. The promoter's sensitivity could be too high, so it reports concentrations below levels of real-world interest. Alternately, the promoter's sensitivity could be too low, so it reports concentrations above those which mark the boundary between "safe" and "dangerous." A second limitation is the the behavior of the PoPS output from the promoter; for example, output may vary linearly with input. This type of response is incompatible with a digital "safe" or "dangerous" output.

Our Solutions

  • A Sensitivity Tuner: To avoid being limited to the sensitivity of the promoter and in order to be able to detect distinct concentrations of an inducer using just one promoter, we see the need for a set of sensitivity tuners. These devices allow you to "tune" your biosensor, such that it reports meaningful concentrations of the inducer appropriate to the biosensor's application. The sensitivity tuner also modifies the PoPS output from the promoter's native behavior to a sigmoidal "on" or "off" response pattern.
  • Colour Output: What if we could "see" the concentration of an inducer in a sample by a change in colour of the biosensor? Many prey species are brightly coloured, showing off clearly the fact that they are poisonous or otherwise harmful to potential predators, a phenomenon known as aposematism or warning colouration. Humans use colour as a means of conveying information as well - we can "see" if a child has a fever using a thermometer strip and we can "see" the pH of a solution using a pH indicator. Colour can be a meaningful but simple output solution for biosensors, adapting nature's idea of warning colouration.

Project Details

Design

The Product

The Product

We envisioned a marketable product that reports the concentration of an inducer by colour. Imagine a dipstick with wells, each of which contain pigment-expressing bacteria in response to an inducer. However, each strain is sensitive to a different concentration of the inducer. The concentration of the inducer in the test solution can be determined by reading the pattern of pigmentation.







The Genetically Engineered Machine

The Genetically Engineered Machine

Each bacterial strain is a machine built from a three part system.

  • Sensor: The sensor system is sensitive to different concentrations of an inducer.
  • Sensitivity Tuner: This device is responsible for the setting the sensitivity to the inducer, and acts as an "on" switch to activate pigment production once the inducer has reached a threshold.
  • Colour Generator: Responsible for pigment production.

Components

The three part system can be abstracted by the diagram below:

Abstraction6.jpg

The components of each of the black boxes is as follows:

Cambridge systemdiagram7.jpg

The sensor, sensitivity tuner, and colour should be viewed as separate parts that are pieced together to build a tunable biosensor that utilizes colour as output. The Parts Registry already has an impressive selection of parts that can be used as sensors. The Cambridge 2009 iGEM team focused on developing a selection of different sensitivity tuner parts and a selection of different pigment producing parts.

  • Sensitivity Tuner: These constructs are based on Cambridge 2007's amplifiers. The general construct is composed of a gene coding for a phage activator protein and a phage activator-sensitive promoter. With PoPS input, the phage activator gene is transcribed. After translation to produce the phage activator protein, the protein binds to the phage activator-sensitive promoter to activate transcription. Thus it is a device that generates a distinct PoPS out given a PoPS in. With an input-sensitive promoter alone, output generally varies linearly with input--this, at least, is the case with the arabinose-sensitive promoter pBad/Arac (BBa_I0500). However, when a sensitivity tuner is placed downstream of the input-sensitive promoter, the output versus input behavior is altered such that output increases dramatically at a certain input, resulting in sigmoidal behavior with a distinctive threshold.
  • Colour Generator: Though E. coli does not naturally produce pigment, several other bacterial species secrete pigmented antibiotics. We mined bacterial genomes for pigment-producing operons, and transformed the most promising candidates into E. coli.

Kits of Parts

The culmination of our project was to generate and characterize two kits of of parts - one of Sensitivity Tuners and one of Colour Generators.

Sensitivity Tuners: There are 3 different activator genes and 5 different activator-sensitive promoters in the registry. 15 combinations are possible, and each has a distinct threshold and peak rate of output. The table below summarizes the parts we designed and characterised:

P2 ogr activator PSP3 pag activator phiR73 delta activator
PF promoter
PO promoter
PP promoter
Psid promoter
PLL promoter

Colour Generators: We have devoted our summer to 3 different pigment systems:

  • Carotenoids: The enzymes required for carotenoid production originally come from Pantoea ananatis, and were available in the registry. We used them to produce orange and red.
  • Melanin: The tyrosinase required for melanin production originally comes from Rhizobium etli and produces brown.
  • Violacein: The enzymes required for voilacein production originally come from Chromobacterium violacein. The operon can be manipulated to produce violet and two shades of green

We designed and characterised the following biobricks:

Biobrick Colour
Red
Orange


Brown
Violet
Dark Green
Light Green


Potential exists to expand both of these kits of parts further using more phage activators and phage promoters that are not yet in the registry

Cambridge Sponsor Logo1.pngCambridge Sponsor Logo2.pngCambridge Sponsor Logo3.pngCambridge Sponsor Logo4.pngCambridge Sponsor Logo5.pngCambridge Sponsor Logo8.pngCambridge Sponsor Logo6.pngCambridge Sponsor Logo7.pngCambridge Sponsor Logo9.pngCambridge Sponsor Logo10.pngCambridge Sponsor Logo11.pngCambridge Sponsor Logo12.pngCambridge Sponsor Logo14.pngCambridge Sponsor Logo13.pngCambridge Sponsor Logo15.pngCambridge Sponsor Logo16.pngCambridge Sponsor Logo17.pngCambridge Sponsor Logo18.pngCambridge Sponsor Logo19.pngBmglab.jpg