Team:Minnesota/Project

From 2009.igem.org

(Difference between revisions)
Line 30: Line 30:
We also examined 4 mutations in the Tet operator site for each construct.
We also examined 4 mutations in the Tet operator site for each construct.
 +
 +
 +
 +
 +
 +
 +
 +
<h2>Methods</h2>
<h2>Methods</h2>
 +
 +
<h3>Preparing Competent Cells</h3>
 +
<ol>
 +
<li>Grow a streak isolation plate overnight for TOP10 and DH5αPro cells.</li>
 +
<li>Inoculate single colony from the freshly streaked plate to 2 ml LB media.</li>
 +
<li>Grow culture for 16 hours at 37 °C and 220 RPM</li>
 +
<li>Then inoculate 80 ml of media with 800 µl of the culture and grow for 2 hours at 37 °C and 220 RPM.</li>
 +
<li>Shake the culture in an ice bath for 10 minutes while chilling 4 50 ml tubes.</li>
 +
<li>Transfer the culture into 2 50 ml tubes for both TOP10 and DH5αPro</li>
 +
<li>Spin the culture at 5000 RPM and 4 °C (maintain this temperature as much as possible at this point).  Throw the supernatant.</li>
 +
<li>Add 20 ml of chilled 100mM CaCl2 to the tube and re-suspend by vortexing</li>
 +
<li>Incubate on ice for 40 minutes</li>
 +
<li>Spin culture at 4500 RPM and 4 °C for 10 minutes.  Throw the supernatant.</li>
 +
<li>Add 3.5 ml of 100 mM CaCl2 and 1.5 ml of 50% Glycerol and gently re-suspend by tapping the tube (do not vortex).  Pre-chill micro centrifuge tubes.</li>
 +
<li>Transfer 200 µl of the culture to the micro centrifuge tubes, snap freeze and store at -80 °C.</li>

Revision as of 17:58, 7 August 2009

Mnlogo.jpg
Home The Team The Project Submitted Parts Modeling SynBioSS Designer Parts Characterization Experiments and Calendar

Contents

The Project

AND Gates

How it works

ANDgatetable.jpg
AND Gates are logic circuits that produce an output if and only if two inputs are present. For example, our system produces GFP only if two small molecules named aTc and IPTG are present. If one of them is not present, no GFP will be produced. Ideally an AND gate will obey the truth table shown to the right, where 1 means the input is present, and 0 means that it is not.

In order to get this behavior, we take advantage of the structure of promoter sequences in prokaryotes. When RNA polymerase(more specifically the sigma factor) binds to the promoter, it binds to region at -35 and -10 relative to the transcriptional start site. Since the entire sequence is not used by the sigma factor, there are three regions of DNA that can be changed to provide AND gate behavior. These are the upstream of -35, between -35 and -10, and downstream of -10. In each of these sites, we can place a DNA sequence that is preferentially bound by proteins in the cell. For this case, the two proteins are TetR and LacI, both of which are constitutively produced by our strain of E. coli(DH5-alpha-pro). In each of the three sites, either a lac or tet operon can replace the normal DNA. In order to create an AND gate, at least one of these sites must be a tet operon and one must be a lac operon.

ANDgate.jpg

We studied the potential of a synthetic, single promoter AND gate. This helps us understand at a fundamental level what is happening in a network with multiple regulators and opens further research paths. The device consists of parts of the Tet (tetracycline) and Lac (lactose) and responds to commonly used inducers IPTG (Isopropyl β-D-1-thiogalactopyranoside) and aTc. Three or fewer of these operators can be combined to form a promoter and the order and quantity of each operator site result in different constructs, that is, given three blank spots for operators on a promoter and the choice of either -, T or L for each spot, there are a variety of possible promoter designs. We chose to focus on four constructs:

  • T T L
  • T T -
  • T - -
  • - T -

We also examined 4 mutations in the Tet operator site for each construct.





Methods

Preparing Competent Cells

  1. Grow a streak isolation plate overnight for TOP10 and DH5αPro cells.
  2. Inoculate single colony from the freshly streaked plate to 2 ml LB media.
  3. Grow culture for 16 hours at 37 °C and 220 RPM
  4. Then inoculate 80 ml of media with 800 µl of the culture and grow for 2 hours at 37 °C and 220 RPM.
  5. Shake the culture in an ice bath for 10 minutes while chilling 4 50 ml tubes.
  6. Transfer the culture into 2 50 ml tubes for both TOP10 and DH5αPro
  7. Spin the culture at 5000 RPM and 4 °C (maintain this temperature as much as possible at this point). Throw the supernatant.
  8. Add 20 ml of chilled 100mM CaCl2 to the tube and re-suspend by vortexing
  9. Incubate on ice for 40 minutes
  10. Spin culture at 4500 RPM and 4 °C for 10 minutes. Throw the supernatant.
  11. Add 3.5 ml of 100 mM CaCl2 and 1.5 ml of 50% Glycerol and gently re-suspend by tapping the tube (do not vortex). Pre-chill micro centrifuge tubes.
  12. Transfer 200 µl of the culture to the micro centrifuge tubes, snap freeze and store at -80 °C.