"
Team:IIT Madras/Experiments
From 2009.igem.org
Ramakrishna (Talk | contribs) (→Comparing the differences in the growth rates of cells with and without plasmids in various media) |
Ramakrishna (Talk | contribs) (→Comparing the differences in the growth rates of cells with and without plasmids in various media) |
||
| Line 63: | Line 63: | ||
Note: After the initial 4 hour incubation (the 3ml cultures), we used this to inoculate a 5ml culture with the same antibiotic in the medium as in the 3ml culture. The OD600 of this 5ml tube after the inoculation was 0.01. This was then made to grow for 2.5 hours. This is the culture from which we inoculated the final 16 tubes which would then be used for measurements. | Note: After the initial 4 hour incubation (the 3ml cultures), we used this to inoculate a 5ml culture with the same antibiotic in the medium as in the 3ml culture. The OD600 of this 5ml tube after the inoculation was 0.01. This was then made to grow for 2.5 hours. This is the culture from which we inoculated the final 16 tubes which would then be used for measurements. | ||
| - | Click [[https://2009.igem.org/Team:IIT_Madras/Results#Comparing_the_differences_in_the_growth_rates_of_cells_with_and_without_plasmids_in_various_media | + | Click [[https://2009.igem.org/Team:IIT_Madras/Results#Comparing_the_differences_in_the_growth_rates_of_cells_with_and_without_plasmids_in_various_media here]] for the results |
===Modeling=== | ===Modeling=== | ||
Revision as of 10:33, 21 October 2009
Contents |
Experiments
Comparing the differences in the growth rates of cells with and without plasmids in various media
This experiment helps in comparing the growth rates of various strains in different antibiotic media.
First we inoculate a colony from the plate containing the required strain into its corresponding media (the media with the required antibiotic). That is, DH5a will be inoculated into LB without any antibiotic, RFP (in pSB1C3)containing cells will be inoculated into LB containing Chloramphenicol (Chl), CFP (in pSB1A2)containing cells will be inoculated into LB containing Ampicillin (Amp) and RFP-CFP cotransformed cells into LB containing both the antibiotics. These are then grown for about 4 hours or till they reach an OD600 value between 0.1 to 0.5. Then the culture of each strain is taken and inoculted into each of the 5ml broths which contains no antibiotic, Amp, Chl and Amp-Chl so that the OD value in all the freshly inoculated tubes is 0.01. So we have an array of 16 tubes with various possible combinations:
- DH5a in no antibiotic, DH5a in Amp, DH5a in Chl and Dh5a in Amp-Chl
- RFP (pSB1C3) in no antibiotic, RFP (pSB1C3)in Amp, RFP (pSB1C3)in Chl and RFP (pSB1C3)in Amp-Chl
- CFP (pSB1A2) in no antibiotic, CFP (pSB1A2)in Amp, CFP (pSB1A2)in Chl and CFP (pSB1A2)in Amp-Chl
- RFP (1C3)-CFP (1A2) in no antibiotic, RFP (1C3)-CFP (1A2) in Amp, RFP (1C3)-CFP (1A2) in Chl and RFP (1C3)-CFP (1A2)in Amp-Chl
Thus the starting point for all the samples is the same - an OD600 of 0.01. Every hour starting from the point of inoculation, the OD of all the 16 samples is measured. This will give a fair idea of the growth rates of variuos strains in different antibiotic media
Experimental protocol:
- A colony of DH5a is inoculated into 3ml LB without any antibiotic in a 50ml centrifuge tube. Similarly, RFP (1C3) colony is inoculated into 3ml LB with Chl, CFP (1A2) colony into 3ml LB with Amp and RFP-CFP colony into 3ml LB with Amp-Chl.
- This inoculum is allowed to grow for about 4 hours or till the OD600 of each sample crosses 0.1.
- Then we use OD 1 x Vol 1 = OD 2 x Vol 2 to measure how much to inoculte from this 4 hour culture to each of the fresh 5ml LB medium with different antibiotic combinations so that the starting OD is 0.01. In this case, OD 1 is the OD600 of the 4 hour culture, Vol 1 is the volume of this 4 hour culture that needs to be inoculted in to the fresh 5ml culture, OD 2 is 0.01 (starting OD for all the 5 ml cultures) and the Vol 2 is the final volume (5ml + vol 1).
- From this freshly inoculated sample, 150ul of the culture is used to measure the OD every hour starting from the point if inoculation. The 150ul of the sample is diluted 5 times to 750ul and then the OD600 is measured.
- The whole procedure is repeated again to check for reproducibility.
Note: After the initial 4 hour incubation (the 3ml cultures), we used this to inoculate a 5ml culture with the same antibiotic in the medium as in the 3ml culture. The OD600 of this 5ml tube after the inoculation was 0.01. This was then made to grow for 2.5 hours. This is the culture from which we inoculated the final 16 tubes which would then be used for measurements.
Click [here] for the results
Modeling
Fluorescent Imaging
