Team:TorontoMaRSDiscovery/Notebook

From 2009.igem.org

Revision as of 15:48, 4 September 2009 by Djj (Talk | contribs)

Contents

April 27, 2009

  1. Received from Rosa (SPiT):
    • TM0785
      • Plasmid containing encapsulin
      • Recommend transfect into bacteria and re-sequence
      • See email note regarding sequence error
    • 0.5 microliters TMG DNA 100 microgram/microliter
      • Use 0.4 microliter for 50 microliter PCR reaction
      • This is thumotoga maritime genomic DNA for purpose of re-cloning
  2. Microcentrifuge tubes 1 and 2 placed in -20 freezer

May 15, 2009

  1. pH buffers received from VWR Mississauga
    • pH 4 buffer (red) 500 ml
    • pH 7 buffer (yellow) 500 ml
    • pH 10 buffer (blue) 500 ml
      Above are used for pH/mV Meter calibration
  2. pH/mV meter calibrated according to manual – recorded in index
  3. Ethanol solution (70%) made from 85% ethanol

May 19, 2009

  1. 2L of TE buffer made (10X TE)
    Recipe for 2L from stock solution (10X TE)
    a) 10 ml 1M Tris-HCl pH 7.5-80.0 x 2 = 20 ml
    b) 2 ml 0.5 M EDTA pH 8.0 x 2 = 4 ml
    c) 988 ml ddH20 x 2 = 1976 ml
    To make Tris-HCl, Tris base is used and adjusted to desired pH using HCl
    1 M Tris base is required of which 20 ml is required – thereby 2.4228 g Tris base (due to scale limitations, 2.42g of Tris Base was used
  2. 500 ml of 1 M Tris Base made
    mass of Tris used = 1M/1000 ml x 500 ml x 121.14 g/mol = 60.57 g
    volume of water used = 500 ml
  3. 250 ml of 0.5 M EDTA solution was made
    mass of EDTA used = 36.53 g
    observations: EDTA did not dissolve in ddH2O on heat and being stirred

May 21, 2009

  1. Retrieved autoclaved ddH20, glycerol solution
  2. Gel Electrophoresis (test run)
    • 1% gel: 0.5 g agar mixed with 50 ml of 1X TBE
    • 10X TBE diluted with 5 ml TBE + 45 ml ddH20 – did not use all 50 ml for 1 gel (gel will be too thick – make 2 instead)
    • Loading Dye: add glycerol solution to 25 mg bromophenol blue then add dH20 to 10 ml (to make 6X)
    • Running gel: match wells to black side, run at 120 mA
  3. Visualize Gel in UV
    1. Turn power on
    2. Gel in machine face up
    3. Close door securely
    4. Turn white light on
    5. Adjust zoom, contrast, focus from black dial on top of machine
    6. Turn white light off (turns on UV)
    7. Press ‘live’ toggle – acq. Should be 0.4 sec.
    8. Print if desired or save on floppy disk
    9. Turn power off
    10. Dispose of gel in proper container
    11. Close door

May 25, 2009

  1. Made overnight bacteria culture (200 ml LB: 20 microliters DB3.1)

May 26, 2009

Retrieved from "http://2009.igem.org/Team:TorontoMaRSDiscovery/Notebook"