Team:Sheffield/Project

Overall project

In this project, we originally intended to create an E.coli system that is sensitive to multiple wavelengths of light and produce a colour indication of the specific wavelength it is exposed to. However due to limitations in the time and number of people available, and due to unexpected results the project changed significantly.

In the end, our project became: characterizing existing parts, such as BBa_R0082 for beta-galactocidase activity depending on time from the reaction start as well as wavelength and intensity of exposed light.

Project Details

The first experiment we carried to familiarise ourselves with the strain, was to repeat the light sensing ability of RU1012 as described in the Levskaya et al. paper[1], in its most simple form. Red light switch off the photoreceptor through inhibiting autophosphorylation, and therefore switching off the expression for Lac Z production. We shown borad spectrum light on one sample and kept the other in the dark so that gene expression can not be interefered. The samples were put on seperate agar plates with X-gal on it which acts as a substrate for Lac Z and producing a blue colouration. To our surprise, the result were opposite to what we expected: the illuminated plate produced more pigment than the one in the dark, whereas it should have been the opposite. No control was used in this experiment.

The same experiment was repeated with a control strain to confirm that the result was systematic. Later on we realise that the wavelength that inhibits the autophosphorylation has to be a specific wavelength, a broadspectrun light that contains that wavelength does not have the same effect. Too solve that problem we have tried various measures:

Hydrogen lamp

The Balmer lamp provided a narrower band of wavelength, we hoped that it can characterise the E.coli system better than broad spectrum light. Experiments were repeated with Hydrogen lamp, conducted at room temperature - due to set up of the lamp, the experiment can not be carried out in an incubator at 37C. Unfortunately, this has not changed the outcome of the result, the gene expression was still not switched off.

To compensate the fact that the experiment was conducted at room temperature, L-arabinose was added to the agar plates as an inducer for the conversion of heam to phycocyanobillin - forms part of the photoreceptor. However, results still remained unchaged. Further investigation was carried out, we contacted authors of the article and asked for their help and extracted the fact that to deactivate the phytochrom of the transformed E.coli RU1012, the wavelength used can only be very narrow band of red light. We also extracted that the intensity of the light is also significant to the deactiation.

The response from the authors inspired us to characterise the two gene system further in terms of the optimum wavelength and intensity for gene expression deactivation. The gene expression is also apparently leaky

Filter paper

A range of filter paper which only let through certain band of wavelength was used; blue(450-495nm),red(620-750) and green(495-570). All samples was were wrapped in different filter paper and incubated for 12hrs at 37C, photos of samples were taken as a time series to show the progress of the colouration. Result at 12hrs was left out of the time series because it was identical to 9hrs results.

Varying light intensity

After verifying that red light inhibits the most gene expression, the characterisation of the intensity can be proceed. According to the research paper, the light intensity can effect the amount of gene expression in this system. To investigate this, 3 sample and a control strain were put into LB broth, was then exposed to red light for 12hrs at the following intensity uEins/m2/s: 2.5, 6, 7, 10. Miller Assay was then performed to measure the amount of beta-galactocidase produced at each intensity by measuring the optical density of each sample in a photo-spectrometer.

Results

Characterisation of the system

Graphs above shows the model of LacZ activity over different intensity over the course of 12 hours.

- This model is based on our experimental result and it matches with the model in the paper.

- An important point is that the amount of black precipitate the system produce is not a representation of the amount of LacZ activity, because the black precipitate does not degrades on the agar plate.

-Hence why Miller Assay must be carried out to quantify the amount of LacZ activity.

Graph analysis

3hrs- The system is very unstable, the beginning of translation and transcription of gene, LacZ activity is erratic, does not form a trend proportional to intensity over the first 3 hours.

6hrs- The system is still unstable, but relatively calmer.

9hrs- The system is more similar to expected trend.

12hrs- The system behaves as expected in the paper, LacZ activity decrease as light intensity increase

The control strain has produced a similar trend to the experimental values.

3D Characterisation plot

This 3D plot is generated through Matlab, it models the system's LacZ activity over various light intensity over a course of 12 hours.

Discussion

This link shows the table of measurement taken in order to obtain results shown above.

All the results we have got show trends and strong characterization, which gives an idea how to go about the design.

The error bias of our result cannot be calculated or shown but; to obtain a more accurate result more readings have to be taken.

References

Papers

1. Engineering Escherichia coli to see light
   Nature 24 November 2005 DOI:10.1038/nature04405
   A. Levskaya et al.
   [http://www.nature.com/nature/journal/v438/n7067/full/nature04405.html URL] [http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?cmd=Retrieve&db=pubmed&dopt=Abstract&list_uids=16306980 Pubmed] [http://www.hubmed.org/display.cgi?uids=16306980 Hubmed]