Team:Heidelberg/n4tr1um

From 2009.igem.org

(Difference between revisions)
(DNA synthesis)
(Removing all content from page)
 
(9 intermediate revisions not shown)
Line 1: Line 1:
-
== Transformation of Bacteria ==
 
-
For enrichment of vectors, E .coli DH5α were used. For the transformation 100 µl of the competent cells were thawed on ice and 50 – 400 ng DNA solution added (depending on the concentration of the DNA solution). After a 30-60 minute incubation on ice, cells were made permeable for the DNA by heat shocking for 45 seconds at 42 °C and a further 3 minute incubation on ice. The samples were than rescued by adding 500µl preheated antibiotic free LB-medium and incubated for one hour at 37 °C while shaking for induction of the antibiotic resistance. The selection for plasmid containing and therefore antibiotic resistant bacteria was conducted by plating them on antibiotic containing LB-agar plates.
 
-
== Isolation of plasmid DNA by alkaline lysis (mini and maxiprep) ==
 
-
For analysis of ligations and transformations QIAprep Spin Kits (Qiagen, Hilden) were used following the manufacturer instructions. For miniprep a single colony was picked from a LB-agar plate or glycerol stock was used to inoculate 5 ml LB-medium with appropriate antibiotic for selection (100 µg/µl ampicillin, 50 µg/µl kanamycin, 35 µg/µl chloramphenicol). Bacteria were grown over night at 37 °C while shaking (200 rpm). By using 4 ml over night culture with this kit the yield was around 6-10 µg. For maxipreps the Qiagen CompactPrep Plasmid Maxi Kit was used following the instructions given by the instruction manual. In this case 250 ml LB-medium were inoculated and used for preparation of plasmid DNA. The routinely yield was 300-400 µg plasmid DNA. Purity and amount of DNA was analysed using a NanoDrop.
 
-
 
-
== Site-directed mutagenesis ==
 
-
For removal of unwanted Restriction Sites, a PCR-based site direct mutagenesis protocol was adapted from [http://www.stratagene.com/manuals/200518.pdf Stratgene]. Oligos were designed to have a high (>78°C) Tm ny applying the formula
 
-
<math>T_{m} = 81{,}5 + 0{,}41 * (%GC) - \frac{675}N - %mismatch</math>.
 
-
The following scheme was used for pipetting:
 
-
{| class="wikitable"
 
-
|- bgcolor=grey
 
-
! height=20px, width=900px |
 
-
|-align="center"
 
-
| style="font-weight:bold;" | 1 µl  template (10 ng)
 
-
|-align="center"
 
-
| style="font-weight:bold;" | 1 µl  primer 1 (25µM)
 
-
|-align="center"
 
-
| style="font-weight:bold;" | 1 µl  primer 2 (25µM)
 
-
|-align="center"
 
-
| style="font-weight:bold;" | 0,5 µl polymerase (Phusion)
 
-
|-align="center"
 
-
| style="font-weight:bold;" | 1 µl  dNTP mix (10 mM)
 
-
|-align="center"
 
-
| style="font-weight:bold;" | 10 µl  5x Phusion HF buffer
 
-
|-align="center"
 
-
| style="font-weight:bold;" |38 µl  dH2O
 
-
|-
 
-
|}
 
-
 
-
The PCR procedure was as follows:
 
-
 
-
{| class="wikitable"
 
-
|- bgcolor=grey
 
-
! height=20px, width=300px | || width=300px| || width=300px|
 
-
|-align="center"
 
-
| style="font-weight:bold;" |Initiale denaturation || 95- 98 °C, 30 sec || 1 cycle
 
-
|-style="height:20px"
 
-
|
 
-
|-align="center"
 
-
| style="font-weight:bold;" |denaturation || 95-98 °C, 10 sec
 
-
|-align="center"
 
-
| style="font-weight:bold;" |annealing/elongation || 72 °C, 30sec/1kb + 30sec || 25-28 cycles
 
-
|-align="center"
 
-
|
 
-
|-align="center"
 
-
| style="font-weight:bold;" |termination || 72 °C, 5 – 10 min || 1 cycle
 
-
|-align="center"
 
-
| style="font-weight:bold;" | || 4 °C || forever
 
-
|-style="height:20px"
 
-
|
 
-
|-
 
-
|}
 
-
 
-
== DNA synthesis ==
 
-
Oligos were designed using [http://baderlab.bme.jhu.edu/gd/ GeneDesign]. 15Bp were chosen as an overhang and 56 °C as an annealing temperature.
 

Latest revision as of 12:26, 24 June 2009