Team:Washington-Software/Notebook

From 2009.igem.org

(Difference between revisions)
(Model A)
Line 106: Line 106:
Video
Video
 +
<html>
<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/QWR_5CgKSn4&hl=ko&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/QWR_5CgKSn4&hl=ko&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>
<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/QWR_5CgKSn4&hl=ko&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/QWR_5CgKSn4&hl=ko&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>
 +
</html>
== Model B ==
== Model B ==

Revision as of 23:14, 13 October 2009

WashingtonColorSeal-21-clip.gif Home Team Project Modeling Notebook

Contents

Progress of the Project

There have been two failures before the final product of this BioBrick-A-Bot. We call this final product as Model C, and here we show Model A and B.

Model A

Model A used 2D Polar Coordinates system and tried from 7/8/2009 to 8/6/2009

Features

Good Features

  1. Simple idea

Neutral Features

  1. Radial Coordinate System(CS)
    • Can be argued as bad, since the 96-well plate well CS is difficult to convert to the Radial Coordinate System.
  2. No programs

Bad Features

  1. Top-Heavy
  2. Front-Heavy:topples easy
  3. Small motor errors leads to big well errors
  4. The NXT Brick on the base is difficult to get out.
  5. Can get stuck easily.


Base(Platform)

Model A Base.png


  • Arm Complex
    • 96-well plate holder(1 needed)
      1. Attach the position 1 of a 15-brick to the position 1 of a 13 brick.
      2. attach the position 1 of a 13-brick to the position 15 of the 15-brick.
      3. Attach a 15-brick to the position 11's of the two 13-bricks.(It should make it look like a parallelogram with
    • Double Arms(2 needed)
      1. Arms(4 needed)
        1. Attach the position 1 of an 11-brick to the position 11 of another 11-brick.
        2. Numbering goess from top to bottom.
        3. Attach the position 5 of an arm to the position 1 of a 15-brick.
        4. Attach another arm's position 5 to the position 15 of the 15-brick.
        5. Numbering: Left arms are labeled as with a prime before(like '3, plural like '1's), right arms have a prime after (like 3', plural like 1"s), and the 15-brick is labeled as before.
    1. Attach the left leg(end) of a plate holder to the '1's of two double arms(one above, one below).
    2. Attach the other leg to the 1"s of the double arms.(There isn't any choice for whether to put it above or below).
  • NXT Brick Complex (1 needed)
    • NXT Brick Sub-Complex (1 needed)
      1. Attach the 2-Sensor-Hole position of an NXT Brick to the 2-position of a 13-brick.
      2. Attach the 5-Sensor-Hole position of the NXT Brick to the 2-position of another 13-brick.
      3. Nxt-Brick numbers as before, the 13-brick on the 2-Sensor Hole position is the same with a prime before, and the other 13-brick has a prime after.
    1. Attach the 4-hole of a 11-brick to the '12 hole of the NXT Brick Subcomplex, and the 8-hole of the 11-brick to the 12'hole of the Subcomplex.
    2. Attach the 1-hole

Pipet Holder

Robot A Pipet Holder.png


  • Crossbeams(2 needed):
    1. Attach the center of an H-Bracket to position 2 of a 9-brick.
    2. Attach another H-bracket to the 9-brick in position 5.
  1. Put the crossbeams such that the H-Brackets are aligned.
  2. Attach two 9-bricks to the H-brackets, on the positive side of the other 9-bricks.(hole-hole)
  3. Attach a black H with a +-shaped hole in it to the 8,9 position on a non-crossbeam 9-brick.
  4. Push a 12-rod through the +-shaped hole.
  5. Put the following onto the rod: a rod-blocker, two worm-toothed gears(aligned), and another rod blocker.

Video

Model B

Model B used 3D Cartesian Coordinates system. It was built and tested from 8/6/2009 to 8/26/2009

Here are the pictures of the Model B


Movement Assembly(NXT Brick 1)

  • Three racks, connected to three motors to position the pipet head.


Pipet Assembly (NXT Brick 2)

  • Motors on brick: From top to bottom,
    1. Compression pumps for cleaning pipet, and
    2. Pneumatic control for sucking/expelling liquid.


Video

<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/T-QcGSe8bwY&hl=ko&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/T-QcGSe8bwY&hl=ko&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>

Notebook

Here are some of notebook pages that show the calculations and scratches of the robot.

Notebook Page 1.jpg Notebook Page 2.jpg Notebook Page 3.jpg Notebook Page 4.jpg Notebook Page 5.jpg Notebook Page 6.jpg