Team:UNIPV-Pavia/New Parts

From 2009.igem.org

EthanolPVanimation.gif



Our new parts


Our new parts:

Re-built existing parts (BBa_our part code/BBa_existing part code)

Existing parts from the Registry

Existing parts: sequence debugging


BBa_K173003 - ethanol producing device

Description

This device takes PoPS as input and produces pyruvate decarboxylase (pdc) and alcohol dehydrogenase II (adhB) enzymes.

Pyruvate decarboxylase (pdc, ) catalyses the decarboxylation of pyruvic acid to acetaldehyde and carbon dioxide, while alcohol dehydrogenase II (adhB, ) catalyses the acetaldehyde reduction to ethanol. The latter enzyme, as reported in the literature, is also able to work in the opposite direction, oxidizing ethanol to acetaldehyde. The two enzymes come from Zymomonas mobilis ethanologenic bacterium and constitute an essential step of alcoholic fermentation.

So, this device contains the minimum set of genes that are required to engineer a heterologous fermentation pathway.

The coding sequences of pdc and adhB genes have been optimized for Escherichia coli codon usage.

Pv A5new2 3 BBa K173003.png

Characterization

Qualitative phenotype characterization

PLATES RESULTS

This device has been cloned downstream of 4 different promoters, one of which in two different vectors. These assemblies were transformed in TOP10 and gave the following phenotypes when bacteria were plated on LB agar plates or on LB agar plates + 2% glucose (all the plates have been incubated at 37°C for about 11 hours, then some colonies were picked with a sterile tip and plates were incubated for additional 10 hours):

upstream promoter plasmid promoter RPU in LB colony phenotype
1.58 [1.56; 1.67] small colonies
not estimated small colonies
0.69 [0.64; 0.73] small colonies
~0 without induction normal colonies
not estimated normal colonies

These results demonstrate that a constitutive expression of pdc and adhB gives a high metabolic burden to E. coli, in fact the only normal phenotype on plates was with non-induced device. Only this assembled part has been submitted to the Registry, as .

BBa_F2620-BBa_K173003 in pSB1AK3 plate: example of normal size colonies.
BBa_K173005-BBa_K173003 in pSB1AK3 plate: example of small size colonies.


LIQUID CULTURES RESULTS

Grown cultures of and after the FIRST INOCULUM showed different phenotypes (qualitative analysis), as a function of the used protocol. was the regulated operon, was the promoterless operon, was the promoter alone, pSB1AK3 was a high copy plasmid and pSB4C5 was a low copy plasmid.


PROTOCOL#1 RESULTS (i.e. shaken anaerobic falcon tubes, no glucose):

BioBrick plasmid induction
with 3OC6-HSL
phenotype
pSB1AK3 no normal growth
pSB1AK3 no normal growth
pSB4C5 no normal growth
BBa_F2620 ALONE
- negative control
pSB1A2 no normal growth


PROTOCOL#2 RESULTS (i.e. unshaken anaerobic falcon tubes, 2% glucose):

BioBrick plasmid induction
with 3OC6-HSL
phenotype
pSB1AK3 no a lot of foam in the upper side of the culture;
a strangely big and cloudy pellet after 4000 rpm centrifugation.
pSB1AK3 100 nM no growth
pSB1AK3 1 uM no growth
BBa_F2620 ALONE
- negative control
pSB1A2 no normal growth
BBa_F2620 ALONE
- negative control
pSB1A2 100 nM normal growth
BBa_F2620 ALONE
- negative control
pSB1A2 1 uM normal growth
pSB1AK3 no normal growth


PROTOCOL#3 RESULTS (i.e. shaken anaerobic falcon tubes, 2% glucose):

BioBrick plasmid induction
with 3OC6-HSL
phenotype
pSB1AK3 no higher amount of bacterial pellet than in the negative control (BBa_F2620)
after 4000 rpm centrifugation
pSB1AK3 100 nM no growth
pSB1AK3 1 uM no growth
pSB4C5 no a bit higher amount of bacterial pellet than in the negative control (BBa_F2620),
but lower than in pSB1AK3 after 4000 rpm centrifugation
pSB4C5 1 uM a bit higher amount of bacterial pellet than in the negative control (BBa_F2620),
but lower than in pSB1AK3 after 4000 rpm after 4000 rpm centrifugation
BBa_F2620 ALONE
- negative control
pSB1A2 no normal growth
BBa_F2620 ALONE
- negative control
pSB1A2 100 nM normal growth
BBa_F2620 ALONE
- negative control
pSB1A2 1 uM normal growth
pSB1AK3 no normal growth

These results confirm the metabolic burden given by this BioBrick when gene expression is triggered: induced strains bearing a high copy plasmid containing do not survive, while low copy ones can survive even at 1 uM HSL, which is a high induction, according to the characterization results on (see its own page on the Registry and our our characterization experiments on it). We decided to exploit the lux promoter leakage activity for in pSB1AK3 (high copy), while we decided to induce in pSB4C5 (low copy) the with 1 uM of 3OC6-HSL during our fermentation experiments.

The qualitative phenotypes of the grown cultures of and after fermentation in 10% glucose showed that pellets were higher in (in both pSB1AK3 uninduced and pSB4C5 induced) than in and in the negative control .


Moreover, after both inoculum steps, the grown cultures of and (in both pSB1AK3 uninduced and pSB4C5 induced) showed a "sparkling" phenotype, while and in the negative control did not.


Quantitative characterization

1 - Growth of strains bearing:

  • 3OC6-HSL inducible system upstream of the operon in high copy plasmid () uninduced;
  • 3OC6-HSL inducible system upstream of the operon in low copy plasmid () uninduced;
  • 3OC6-HSL inducible system upstream of the operon in low copy plasmid () induced with 1 uM of 3OC6-HSL;
  • 3OC6-HSL inducible system without the operon in high copy plasmid ();
  • a promoterless operon in high copy plasmid ().

has been monitored in selective LB + 10% glucose starting from an inoculum in the microplate reader (figure below).

Protocol: 200 ul aliquots (3 replicates) were taken from a just inoculated 30 ml culture (LB + 10% glucose) of the SECOND INOCULUM of PROTOCOL#3 and let grow in the microplate reader according to the automatic protocol described in Microplate reader experiments. The microplate was "sealed" with parafilm in order to create an anaerobic condition.

Mean values on three wells filled with aliquots of the indicated strains (200 ul) in selective LB + 10% glucose.
Mean values with 95% confidence intervals for the mean on three wells filled with aliquots of the indicated strains (200 ul) in selective LB + 10% glucose.

2 - Ethanol fermentation capability of these strains in 10%w/v glucose-supplemented LB medium has been tested with three different fermentation protocols (see Fermentation experiments for a detailed description).

The main fermentation results can be summarized with the following bar plots. Ethanol and pH have been measured after 48 hours ( PROTOCOL#2, first two measurements) or 24 hours ( PROTOCOL#3, other measurements).

Ethanol production after fermentation of 10% glucose.
pH after fermentation of 10% glucose.

PROTOCOL#1 was tested only on (in pSB1AK3 induced with 100 nM HSL) and as a negetive control. This protocol resulted in bacterial death for (in pSB1AK3 induced with 100 nM HSL) because of the previously explained metabolic burden when pdc and adhB gene expression was triggered at high levels in a high copy plasmid.


Comments:

The pH results suggest that in strains bearing expressed pdc and adhB the fermentation does not give high levels of organic acids as in negative control strains which do not have pdc and adhB. It is surprising that the pH of BBa_K173003 in pSB1AK3 (pdc and adhB without any promoter) is higher than in the negative control. This could be due to a weak spurious transcription of pdc and adhB, amplified by the high copy number plasmid. This may re-direct part of pyruvate metabolism to ethanol and not to organic acids. Of course this phenomenon should be further investigated.

The results about dynamic growth (in terms of O.D.600) are in accordance with the pH results, confirming that strains bearing BBa_K173021 in pSB1AK3 produce less organic acids than the negative controls, hopefully thanks to pdc and adhB which re-direct the metabolism of pyruvate from organic acids to ethanol, and consequently grow better (to OD600=~1). No significant difference was noticed in the growth of promoterless operon, uninduced and induced BBa_K173021 in pSB4C5, suggesting that in promoterless operon transcription could be activated in unspecific manner (i.e. without a promoter upstream). These three cultures reached OD600 values of ~0.7, while the negative control () reached only OD600=~0.4.

Fermentation results showed that strains bearing expressed pdc and adhB in pSB1AK3 high copy plasmid can produce less ethanol than the negative controls in both PROTOCOL#2 and PROTOCOL#3. Our hypothesis is that in our working conditions adhB converts part of the fermented ethanol back to acetaldehyde, in fact this enzyme is able to perform both acetaldehyde conversion to ethanol and the opposite reaction.

On the other hand, if we add 1%w/v of ethanol in the medium this strain can ferment 30 g/l of ethanol, which is about 60% of theoretical yield. This may be due to adhB behaviour, which was reported in literature to be activated by ethanol accumulation.

Moreover, It is possible that when starting from less than 1% of ethanol in fermentation medium ethanol production could be increased, because in our experiment the bacterial culture reached ethanol concentration survival threshold (40 g/l) and so it difficult to ferment more than 30 g/l.

Conclusions

Ethanol production in this operon has been proved for when assembled under the control of HSL receiver device, yielding composite part.

Promising working conditions have been found for it:

  • BBa_K173021 in pSB1AK3 (HC) not induced with 3OC6-HSL (exploiting basic transcriptional activity), induced with 1%w/v of ethanol;
  • BBa_K173021 in pSB4C5 (LC) induced with 1 uM of 3OC6-HSL.

Increased pH and growth in ethanol producing strains are also proves that the pyruvate metabolism is re-directed from organic acid fermentation to ethanol production. Further work has to be performed to fully understand pdc and adhB optimal working conditions and to optimize the environment for a high yield ethanol production.

Top

BBa_K173007 - aTc inducible device with J23100 promoter

Description

This is an aTc sensing device.

promoter drives the constitutive production of tetR repressor (), which inhibits tetR promoter () activity. When aTc is added to the medium, it binds tetR and inhibits it. So, the PoPS output is a function of the aTc concentration.

A tight regulation is expected for this inducible system because BBa_J23100 is a strong promoter and so tetR repressor should be produced at extremely high levels.

Pv A6 BBa K173007.png

The data below are referred to , which is the measurement system of .

Characterization

aTc concentration
[ng/ml]
LB M9 supplemented
Doubling time [minutes] RPU mean [range] Doubling time [minutes] RPU mean [range]
0 36 0.05 [~0 ; 0.15] 59 0.03 [ 0.02 ; 0.04]
25 32 0.12 [~0 ; 0.19] 61 0.03 [ 0.02 ; 0.04]
50 34 0.17 [0.05; 0.25] 57 0.04 [ 0.03 ; 0.05]
75 43 0.15 [~0; 0.23] 65 0.03 [ 0.02 ; 0.06]
100 40 0.21 [0.19; 0.23] 62 0.03 [ 0.03 ; 0.05]
200 40 0.25 [0.20; 0.28] 70 0.04 [ 0.03 ; 0.06]
300 43 0.20 [0.18; 0.21] 67 0.05 [ 0.04 ; 0.08]


Growth curves for BBa_K173009 in M9
Growth curves for BBa_K173009 in LB
(dGFP/dt)/OD in LB
(dGFP/dt)/OD in M9
Induction curve of BBa_K173009 in M9
Induction curve of BBa_K173009 in LB

Conclusions

We demonstrated that this part works as expected, sensing the aTc concentration provided in the culture medium. The transfer function of this sensor has been characterized in standard units (RPUs) in two different growth media (LB and M9 supplemented with glycerol), as well as the metabolic burden (in terms of doubling time) which affects E. coli bearing this part.

On the other hand, we did not expect to have a higher GFP synthesis rate per cell after the exponential growth phase than in the exponential phase itself (as reported in the 3rd plot for both LB and M9).

This part shows to have a very low leakage rate (about 0.025 RPU) but also a very low transcription rate for high concentrations of aTc. So, it can be used for tight regulation, in those systems who need very low leakage rates (no gene expressed in absence of inducer) but not for massive protein production.

Unfortunately, the estimated transfer function is very noisy (probably because the measured fluorescence values are very close to blank values), and further experiments should be performed in order to validate these induction curves.

Top

BBa_K173011 - aTc inducible device with J23118 promoter

Description

This is an aTc sensing device.

promoter drives the constitutive production of tetR repressor (), which inhibits tetR promoter () activity. When aTc is added to the medium, it binds tetR and inhibits it. So, the PoPS output is a function of the aTc concentration.

A less tight regulation is expected for this inducible system than in because BBa_J23118 promoter is weaker than BBa_J23100 and so tetR repressor shold be produced at lower levels than in the other sensor.

The data below are referred to , which is the measurement system of .

Pv A12 description.png

Characterization

aTc concentration
[ng/ml]
LB M9 supplemented
Doubling time [minutes] RPU Doubling time [minutes] RPU
0 36 0.51 [0.43; 0.73] 78 0.96 [0.80; 1.23]
25 33 1.36 [1.28; 1.44] 82 1.66 [1.38; 2.11]
50 40 1.39 [1.30; 1.48] 81 1.85 [1.61; 2.27]
75 43 1.25 [1.17; 1.31] 88 1.75 [1.51; 2.15]
100 43 1.40 [1.28; 1.48] 90 1.89 [1.68; 2.34]
200 45 1.37 [ 1.31 ; 1.41] 92 1.75 [1.51; 2.09]
300 48 1.45 [ 1.36 ; 1.55] 94 1.73 [1.53; 2.07]

Growth curves for BBa_K173026 in M9
Growth curves for BBa_K173026 in LB
(dGFP/dt)/OD in LB and M9
(dGFP/dt)/OD in LB and M9
Induction curve of BBa_K173026 in M9
Induction curve of BBa_K173026 in LB

Conclusions

We demonstrated that this part works as expected because GFP is produced as an increasing function of the aTc concentration provided in the culture medium. The transfer function of this sensor has been characterized in standard units (RPUs) in two different growth media (LB and M9 supplemented with glycerol), as well as the metabolic burden (in terms of doubling time) which affects E. coli bearing this part.

On the other hand, as for BBa_K173007, we did not expect to have a higher GFP synthesis rate per cell after the exponential growth phase than in the exponential phase itself (as reported in the 3rd plot).

This part shows a high level of leakage (about 0.5 RPU in LB and 1 RPU in M9) but also high levels of induction for high concentrations of aTc (about 1.45 RPU in LB and 1.7 RPU in M9). For this reason, it can be used in those cases where an important response in terms of gene expression is required in presence of an inducer, but is not suitabe if the absence of expression has to be off when inducer is absent. Its induction range is 0.95 RPU in LB and 0.7 RPU in M9.

The switch point of this device is between 0 ng/ml and 25 ng/ml of aTc in both LB and M9.

Top

BBa_K173010 - lactose/IPTG inducible device with J23118 promoter

Description

This should work as a lactose/IPTG sensor.

promoter drives the constitutive production of lacI repressor (), which inhibits lac promoter () activity. When lactose or IPTG is added to the medium, it binds lacI and inhibits it. So, the PoPS output is a function of lactose/IPTG concentration.

Thanks to the hybrid lac promoter (), designed taking the Plambda promoter () and substituting its cI () binding sites with two lacI binding sites, the behaviour of this device is not a function of glucose concentration because the wild type CAP binding sites are not present in this artificial lac promoter.

The test performed to characterize this device has been done with , which is the measurement system of itself.

Pv A11 description.png

Characterization

  • We inoculated 8 ul of glycerol stock in 5 ml of LB + Amp and incubated it overnight (37°C, 220 rpm).
  • In the morning we diluted 1:100 the culture in two falcon tubes and incubated them under the same conditions as before.
  • After about 6 hours we added IPTG in one of the two cultures (final concentration = 1 mM).
  • Fluorescence and O.D.600 were measured in the microplate reader after additional 4 hours.

Results: both cultures had a comparable O.D.600, but also had the same RFU values, demonstrating that the induced culture did not produce any GFP.

Conclusions

We did not perform any standard measurement on this device because preliminary tests showed that GFP levels of induced and non induced cultures were the same and were equals to negative control.

Unfortunately, we did not check if the sequence of , so we do not know if it was actually correct. Another possibility is that lacI is produced at so high levels that 2 mM of IPTG is not sufficient to induce the lac promoter.

Further tests should be done for this system.

Top