Team:Aberdeen Scotland/parameters/invest 3

From 2009.igem.org

(Difference between revisions)
(Monte Carlo Simulations)
(Monte Carlo Simulations)
Line 4: Line 4:
== Monte Carlo Simulations ==
== Monte Carlo Simulations ==
-
  To test how these values work in our model we utilised what is known as a "Monte Carlo Simulation". This works by running the entire simulation thousands of times, but each time the simulation runs the parameters are randomised. This allows us to easily take three parameters, for example K<sub>LacI</sub>, K<sub>TetR</sub> and K<sub>cI</sub> - and plot each of them on an axis of a three dimensional plot. Each time we run a simulation we randomly chose these three variables between the lower expected limit and the upper expected limit and plot a point in our 3D graph corresponding to the randomly chosen values. This point is then colored to show how the simulation worked. The final style we used was to plot a black point if the cell lysed before the input was added (by accidently triggering itself) or if the cell did not lyse in a given period (usually 9 hours). all simulations which exhibited cell lysis in the desired time frame were plotted in color. The color is matched to the the amount of X that was produced as a percentage of the maximum possible X. This is shown in the image below, which has the K<sub>LacI</sub> axis obscured for easier viewing.
+
To test how these values work in our model we utilised what is known as a "Monte Carlo Simulation". This works by running the entire simulation thousands of times, but each time the simulation runs the parameters are randomised. This allows us to easily take three parameters, for example K<sub>LacI</sub>, K<sub>TetR</sub> and K<sub>cI</sub> - and plot each of them on an axis of a three dimensional plot. Each time we run a simulation we randomly chose these three variables between the lower expected limit and the upper expected limit and plot a point in our 3D graph corresponding to the randomly chosen values. This point is then colored to show how the simulation worked. The final style we used was to plot a black point if the cell lysed before the input was added (by accidently triggering itself) or if the cell did not lyse in a given period (usually 9 hours). all simulations which exhibited cell lysis in the desired time frame were plotted in color. The color is matched to the the amount of X that was produced as a percentage of the maximum possible X. This is shown in the image below, which has the K<sub>LacI</sub> axis obscured for easier viewing.
'''Note that this simulation is run on a model that has LacI repression lifting and quorum sensing both modelled as on/off switches with 100% efficiency.''' We will see the full model and accompanying Monte Carlo simulations in the next section.
'''Note that this simulation is run on a model that has LacI repression lifting and quorum sensing both modelled as on/off switches with 100% efficiency.''' We will see the full model and accompanying Monte Carlo simulations in the next section.
Line 10: Line 10:
[[Image:Monte Carlo Graph 1.jpg|center|700px]]
[[Image:Monte Carlo Graph 1.jpg|center|700px]]
-
  Two interesting points to note are the black areas. The area in the bottom right never lyses because of a combination of K<sub>TetR</sub> being too low and K<sub>cI</sub> being too high. This effect is arises as K<sub>TetR</sub> is reduced - since Holin production turns on only at very low levels of TetR. If K<sub>cI</sub> is high it means the system it requires a large amount of cI to repress the production of TetR. This in turn means that some TetR is stochastically produced which is then free to repress the production of Holin.
+
Two interesting points to note are the black areas. The area in the bottom right never lyses because of a combination of K<sub>TetR</sub> being too low and K<sub>cI</sub> being too high. This effect is arises as K<sub>TetR</sub> is reduced - since Holin production turns on only at very low levels of TetR. If K<sub>cI</sub> is high it means the system it requires a large amount of cI to repress the production of TetR. This in turn means that some TetR is stochastically produced which is then free to repress the production of Holin.
-
  The upper black area is created simply because K<sub>TetR</sub> is so high that it takes a large quantity of TetR to repress Holin production, and hence Holin is produced long before it should be.  
+
The upper black area is created simply because K<sub>TetR</sub> is so high that it takes a large quantity of TetR to repress Holin production, and hence Holin is produced long before it should be.  
-
  We can also see the colour scale showing exactly how much of the glue (molecule X) was present at the point of lysis.
+
We can also see the colour scale showing exactly how much of the glue (molecule X) was present at the point of lysis.
<html>
<html>

Revision as of 12:22, 11 August 2009

University of Aberdeen iGEM 2009

Monte Carlo Simulations

To test how these values work in our model we utilised what is known as a "Monte Carlo Simulation". This works by running the entire simulation thousands of times, but each time the simulation runs the parameters are randomised. This allows us to easily take three parameters, for example KLacI, KTetR and KcI - and plot each of them on an axis of a three dimensional plot. Each time we run a simulation we randomly chose these three variables between the lower expected limit and the upper expected limit and plot a point in our 3D graph corresponding to the randomly chosen values. This point is then colored to show how the simulation worked. The final style we used was to plot a black point if the cell lysed before the input was added (by accidently triggering itself) or if the cell did not lyse in a given period (usually 9 hours). all simulations which exhibited cell lysis in the desired time frame were plotted in color. The color is matched to the the amount of X that was produced as a percentage of the maximum possible X. This is shown in the image below, which has the KLacI axis obscured for easier viewing.

Note that this simulation is run on a model that has LacI repression lifting and quorum sensing both modelled as on/off switches with 100% efficiency. We will see the full model and accompanying Monte Carlo simulations in the next section.

Monte Carlo Graph 1.jpg

Two interesting points to note are the black areas. The area in the bottom right never lyses because of a combination of KTetR being too low and KcI being too high. This effect is arises as KTetR is reduced - since Holin production turns on only at very low levels of TetR. If KcI is high it means the system it requires a large amount of cI to repress the production of TetR. This in turn means that some TetR is stochastically produced which is then free to repress the production of Holin.

The upper black area is created simply because KTetR is so high that it takes a large quantity of TetR to repress Holin production, and hence Holin is produced long before it should be.

We can also see the colour scale showing exactly how much of the glue (molecule X) was present at the point of lysis.