Quorum sensing Revisited

One of the triggering mechanisms of our Pico plumber in order to start glue production, is quorum sensing. Quorum sensing is a response of bacteria to their population density. In the natural system of the marine bacterium Vibro fischeri a small molecule, termed autoinducer, is constantly produced at a low level. This autoinducer molecule (HSL) can freely diffuse in and out the E.Coli membrane. The HSL molecule then diffuses into the surroundings. Other bacteria in the surrounding environment can sense each other via diffusion of HSL through their cell membrane. In the absence of a high density of cells HSL rapidly diffuses into the environment and the HSL concentration is too low to trigger quorum sensing. Quorum sensing is based on a lux-type regulated transcriptional system controlling the production of the autoinducer. In Vibro fischeri, LuxR is encoded on the left side of the operon whereas LuxI is produced on the right side. LuxI together wuth an enzyme always present in the cell, called SAM, together generate in an enzymatic reaction the autoinducer, HSL. The autoinducer HSL together with LuxR form a transcriptional activator for the lux operon, also known as lux box. This complex enables a stronger production of LuxI and LuxR and can been seen as an amplifying loop for LuxI production [1-3].

The issue

In the planning stage of the project, we designed the quorum sensing circuit to have a constant medium production of LuxI in order to activate a lux box on the plasmid where the glue production takes place, in the presence of sufficient cell density:

We are using the lux operon and LacO to give us AND–logic gate to start glue production (here denoted as gene X and gene Y). It is expected that if IPTG is present and there is no HSL within the cell, the promoter starts to produce the glue at a low level. In the presence of HSL and IPTG the promoter starts fabrication of the glue at its maximum level. A possible source of error in our design is that our system might trigger glue production and cell lysis on its own. Having in mind that we have a constitutive medium strength promoter, we need a lower concentration of LuxI. To achieve this LuxI was tagged and a Shine-Dalgarno sequence was used to reuce ribosome affinity to 60%.

The Model

We ran our simulation using the IPTG and HSL concentration outside the cell as inputs. We changed both IPTG and HSL concentration at different times by a switch from low to high to see how the inputs affected the simulation. In our later simulations we simulated both the IPTG and HSL inputs more realistically. We did this applying the sochastic simulation (tau-leap method).

The graph shows the concentration of molecules against the iteration number (which is equivalent to time multiplied by a time-step constant of h=0.5). GFP is a place holder for the glue, P stands for the complex of HSL and LuxR, and finally, IPTG and HSL are the input signals for our cell. IPTG is released at 15000 iterations, whereas HSL diffuses from the outside at 25000 iterations. We want a system to have AND-logic gate, so that both high IPTG and HSL concentration is required for system response. However, it is clearly visible that maximal production of GFP already starts shortly after IPTG gets into the cell. We can conclude from this that the lux-box is activated from within the cell. TThe high production of LuxI and hence, HSl, leads to a high concentration of the HSl-LuxR complex. Moreover, the HSL-LuxR complex is ver stable. This complex cannot diffuse out of the cell as HSL can, so that its concentration can build up very much and hence, activate the lux-box.

Possible Solution

To try to overcome this problem, we have redesigned the system to have LuxI and LuxR on the same promoter but with a lux box in front of both.

The Input-dependent model

For this model, we no longer assume the trivial process of repression of LacI being lifted and Quorum Sensing (QS) being turned on. The LacI repression is now a repression / induction hill function with a K_d of 1200 molecules per cell for IPTG forming the LacI-IPTG complex. We assume IPTG leaks into the cell from outside. We only set the outside concentration of IPTG. For quorum sensing all simply set an elevated exterior HSL concentration which is free to diffuse in. We now include a feedback loop into the QS mechanism. To do this we attach a lux box onto the plasmid producing LuxR and LuxI, as follows:

However, the production strength of this lux box is smaller than that of the lux box for producing X, Y and cI. The strengths are as follows:

Production max for X, Y and cI = 0.44 PoPS (Polymerases-per-second)

taken from the iGEM page of ***** and personal communication with **** on ****

Production min for X Y and cI = 0.013 PoPS

taken from *****

Production max for QS feedback = 0.002 PoPS

Production min for QS feedback = 0.00015 PoPS

These values are taken from the paper “ FIOADAOIDFJAOFJASDIOJASOIJADOAJSDAFOJAFOAJSD”

An important new parameter is K_P. This is the dissociation constant for “P” activating the lux boxes, where P is the LuxR-HSL complex. In the next section we show how the most important results obtained with this model.

Level of K_P required for system to function

here we use a Monte Carlo simulation to determine the value of K_P in molecules per cell that is required for the system to function (note that the IPTG and HSL input levels added are both 10000 molecules)

Relationship between K_TetR, K_CI and K_LacI when K_P is 50

Relationship between K_TetR and K_CI when K_P is 50 and K_LacI is 700

We notice that K_P must be around 50 molecules to let the system function. We will now explore the relationship between K_TetR and K_CI at the value of K_P=50 molecules per cell. for this simulation we set the HSL and IPTG input levels to 50,000 molecules. In our next section we will try to calculate the minimum levels of HSL and IPTG required to activate the system correctly.

The graph shows a great deal of stochastic fluctuation, which shows this system is not very robust. Increasing K_P above 50 greatly increases this problem, as does decreasing HSL outside below 50,000.

Our estimation for K_TetR and K_CI suggest that K_TetR is less than K_CI. We assume the worst case value for these two dissociation constants and set them equal to each other, at K_TetR = K_CI = 7000 molecules per cell.

Required input levels of IPTG and HSL

We start by going from 5,000 molecules to 100,000 molecules for HSL and from 10 molecules to 5,000 molecules for IPTG. we see that the sysem requires only around 2000 molecules of IPTG outside, although it benefits slighty when it is exposed to more. Note that the graphs color bar only extends from 55% of X production to 70% of X production. There appears to be no disernable effect in increasing the HSL outside, although when it is above 70,000 it seems to reduce the stochastic effects that stop the system lysing.

We now look at a graph showing HSL at values below 5000 molecules.

Desired Operation

Here are the following assumptions that need to make

K_P has to be ~50 molecules per cell

K_TetR has to be ~3000 molecules per cell

K_CI has to be ~ 5000 molecules per cell

the input level of HSL has to be ~10,000 molecules

the input level of IPTG has to be ~5,000 molecules

Expected Function