• Home
• Team
• Project
• Parts
• Modelling
• Sponsors
• Lab Book

Project

• Overview
• Choices Rationale
• Characterisation
• Safety
• Judging Comments

Sub-projects

• Metal Intake/Efflux
• Metal Sensing
• Sporulation Tuning
• Population Dynamics
• Stochastic Switch
• Metal Sequester
• Chassis
• Promoter Library

Wet Lab

• Lab Book
• Protocols

Meetings

• Meetings Calendar

Planning

• Timeline
• Ideas

Links

• Helping other teams
• Ethics
• T-Shirts
• iGEM Meetup
• Our City
• Fun and Games
• Sponsors
• Useful Links
• Contact Us
• Press Coverage

Formal Lab Session - 15th September 2009

Stochastic Switch Team

Today we set up another restriction disest of the KinA pMKRQ synthesised brick using NheI and EcoRI we ran this on an 0.8% gel however we think that this may be too dilute and that I why we are not seeing the two bands ogf the digest which are a similar size.

We also set up another PCR of the ara fragment as a back up plan for ligation, in case the last ligation did not work as well as we had planned.

We also mini prepped and digested the sac transformations again, and we found that of the 6 samples we had, a few of them had worked!

Just to confirm however we set up 12 more miniprep cultures again for both sac and ara.

Yesterday we did midipreps of Goksels successful sspb plasmid: this was cut with XbaI and PstI ready for ligation into the ara brick (once it's ligated!).

Metal Sensing Team

Introduction

Yesterday's lab session saw the Metal Sensing team ligate the cadA promoter region with the linearised BBa_J33206 BioBrick (BioBrick containing arsR gene and binding site but with promoter absent). The team also attempted to ligate cotC and linearised pMUTIN4. Both of these ligated products were used to transform DH5-alpha E. coli cells.

Today's work will involve the team looking for transformant colonies on the plates and processing them based on observations. If there are colonies, 12 will be picked and used to inoculate 12 tubes of 5ml LB (+ antibiotic) for mini-preps. If unsuccessful, another attempt at ligation and then transformation will follow. The team will also carry out digests of the 5 midi-preps we had done earlier to prove that they have the correct DNA.

Practical Outline

Here are the tasks the Metal Sensing team need to get done by the end of the day:

1. Check plates for cotC-GFP-smtA transformants and arsR-cadA AND gate transformants
   1. If successful prepare for mini-preps by picking 12 colonies and using them to inoculate 12 tubes of 5ml LB
   2. If unsuccessful, reattempt ligations and transformations in E. coli cells.
2. Digest the 5 midi-prep samples (cotC-GFP-smtA, kinA, pGFP-rrnB, pMUTIN4 and pSB1AT3) to ensure the DNA is correct.
3. Run these digests on gel to analyse.

Observations

It can be seen from the photograph above that there are colonies present on the cotC-GFP-smtA transformant LB + amp plates suggesting that the ligations and transformations were a success. This cannot be said for the cadmium sensor 'transformant' cells which did not yield any colonies on the LB + amp plates.

Procedure

Preparation for cotC transformant mini-preps

To prepare the cotC BioBricks for midi-preps, 12 colonies were picked from the LB + amp plate containing 200ul of transformant cells. These colonies, under aspetic conditions, were then used to inoculate 12 tubes of LB + ampicillin. The tubes were transferred to the orbital incubator for overnight growth at 37ºC.

Digesting midi-prep samples

The digests on the cotC, kinA, pGFP-rrnB, pMUTIN4, and pSB1AT3 midi-prep DNA samples were carried out as follows:

Contents of midi-prep digests

	cotC	kinA	pGFP-rrnB	pMUTIN4	pSB1AT3
DNA (ul)	10	10	10	10	10
Buffer (ul)	2	2	2	2	2
EcoRI (ul)	1	1	1	0	1
PstI (ul)	1	1	0	0	1
BamHI (ul)	0	0	0	1	0
Water	6	6	7	7	6

The digest reactions were allowed to run for 1 hour at 37ºC (waterbath).

Ligation of cadA promoter and arsR BioBrick

Transformation of E. coli with ligated product