Week from August 3rd, to August 9th, 2009

Previous Week

Next Week

August, 3rd

• This week we planned to continue the assembly of the synthetic ethanologenic operon.

• We received DH5alpha, XL1-Blue and DB3.1 competent cells from Bologna iGEM Team. Thank you!!

• We performed 2 screenings for the 7 samples of B3 and for the 7 samples of B4:

• SCREENING 1 - Ojective: check the presence of non-ligated plasmids. We planned not to digest with standard enzymes because the resulting fragments would result either too small or too big. Insert excision would generate a possible 129pb fragment, while vector linearization would generate possible 3Kb or 5Kb fragments. We used ApE to decide the best enzymes to cut. Digestion with XhoI-PstI (6 ul of DNA, final volume 20ul).

• Gel results:
  • Only B3-1 and B3-5 showed the bands with expected length for the correct plasmid.
  • All B4 samples showed the bands with expected lengths!

• SCREENING 2 - Ojective: check the presence of the right insert length for B3 samples, because there was the possibility that B1 vector (pSB1A2) ligated in B0015 vector (pSB1AK3) as an insert. If so, no XbaI site is present in the final plasmid, while correct ligations should show a ~1900bp fragment as an insert. Digestion with XbaI-PstI (2 ul of DNA, final volume 20ul). We decided to perform the reaction for all B3 samples, even if only two were good.

• Gel results: B3-1 and B3-5 showed the expected bands for pSB1AK3 (~3200 bp) and B1-B0015 ligated insert (~1900bp).

• We sent the following purified DNA samples to BMR Genomics for sequencing:
  • B3-1
  • B3-5
  • B4-2
  • B4-4

• LB agar plates + Kan preparation.

Preparation of experiment with Tecan F200

• We inoculated 10 ul of A1, A2, A7, J23100, J23101 and J23118 glycerol stocks in 5 ml of LB + Amp, while we used a single colony from B0030 native plate to infect 5 ml of LB + Amp.

• We incubated these inocula overnight (37°C, 220 rpm).

August, 4th

Preparation of experiment with Tecan F200

• We diluted 1:1000 the overnight cultures of A1, A2, A7, J23100, J23101, J23118 and B0030.

• We incubated the diluted cultures for 5 hours (37°C, 220 rpm).

• We adjusted OD600 to 0.03 diluting the cultures in LB + Amp.

Experiment with Tecan F200

• Description
• Purpose:
• Materials & Methods
• Protocol
• Results

August, 5th

• We received sequencing results for the first two ligation steps of ethanologenic operon and for iGEM stabs:
  • B1-13: sequence ok!
  • B2-5: sequence ok!
  • K116001: the stab actually contained K116002! moreover, sequence analysis showed an inconsistent prefix and an additional "c" at the end of nhaA promoter.
  • K116002: the stab actually contained J33204!
  • K112405: sequence ok!
  • P0412: sequence ok!
  • I746902: sequence ok!
  • I746903: the RBS in the sequence is actually B0030 and not B0034 as documented on the Registry. Anyway, it does not corrupt the function of this brick and the rest of the sequence was ok!
  • K101017: very bad sequencing.
  • F2620MIT1: sequence ok!
  • F2620MIT2: sequence ok!

August, 6th

• We received Ethanol Assay Kit and Lactose Assay Kit from BioVision.

August, 7th

• Miniprep for:

• We stored purified DNA at -20°C and next week we will perform digestion for these 12 samples, in order to: i) finish the assembly of the ethanologenic operon, ii) re-assemble A11, which sequence analysis showed a deletion and iii) build up an inducible lysis device.

Previous Week

Next Week