Team:Groningen/Modelling/Characterization

From 2009.igem.org

Revision as of 19:37, 21 October 2009

We have the following parts that we can characterize (RPS stands for Relative Promoter Strength)

v5(RPS) = v5wt + Δv5*RPS

v5(0) = v5wt + Δv5*0
v5(S) = v5wt + Δv5*S

Δv5 = (v5(1) - v5(0))/S

Asbound(As(III)in)
 = S Bmax As(III)in^n
    / (K^n + As(III)in^n)

S(max) / S(0) = ars(max) / ars(0)
S(max) / S(0) = arsT / ars(0)
S(max) / S(0) = 1 + ArsR(0)²/KAd²
      ArsR(0) = KAd √(S(max)/S(0) - 1)

0 = βRN ars1(0) - (ln(2)/τR) ArsR(0)
0 = βRN ars1T S(0)/S(max)
     - (ln(2)/τR) KAd √(S(max)/S(0) - 1)
βRN ars1T S(0)/S(max)
 = (ln(2)/τR) KAd √(S(max)/S(0) - 1)
βRN τR = (ln(2)/ars1T) KAd
   (S(max)/S(0)) √(S(max)/S(0) - 1)

Uptake measurements

To obtain data for the optimization procedure described above we conducted ICP-MS measurements on our cells containing various devices/parts. To optimize our findings we have conducted measurements both in time and in concentration. Details on ICP-MS the experiments can be found on our Protocol Page. Measurements have been conducted at times and concentrations as indicated in the table on the right. Results can be seen below.

First Uptake Measurement
In this case we looked at the arsenic uptake of our wildtype and of our wildtype with a lot of pArs promoters with RFP. The raw data can be found at our Download Section

Getting (Vc/Vs) and other conditions
To effectively determine our constants we need to give our model some extra information. For instance what kind of constructs are inside the cel for a given experiment. Also we need to give the model the volume of cells per liter of fluid. To optain this we use the obtained dry weight and calculate how much wet weight it would have been (assuming dry weight/wet weight = 0.3) and then use the density of E. coli (1100kg/m³) to obtain the cell volume for our sample and eventually the desired volume of cells per liter. Also we need the absolute value of Arsenic taken up by the cells in the assumption that we have one liter of sample and we know (Vc/Vs). Once we know all these parameters the optimization procedure can start.

Fluorescence Measurements
Apart from giving our model all the conditions it needs to calculate all the constants by means of the optimization procedure, we have also conducted some fluorescence measurements and made growth curves of our construct with the pArs promoter with RFP. The cells where put into a solution with either no arsenic in it or at a concentration of 100 micromolair. On the left side one can see the graph of the luminance and on right side and on the right side one can see the coresponding grow curves. The raw data of these measurements can again be found under our Downloads

Second ICPMS measurement For our second measurement I would like to refer to our Accumulation page. These measerments where higher than expected and they need further analyses before we can use them in tha characterization of our parts.

Optimization procedure

To fit our model to experimental data from different uptake experiments and/or papers we have implemented an optimization procedure that allows for experiments with different genotypes and circumstances by letting constants be overridden per experiment. It aims to optimize the sum of the RMS errors for each experiment using Simulated Annealing. By clicking the button "Fit" the optimization is started and its progress can be followed by looking at the table of constants and the graphs shown below the table (which are updated in real-time as the best solution is improved).