• Gel (from left)

1. control -
2. 2-6 - samples (annealing temperature increases to from the left to the right)
3. 7-11 - samples with DMSO (annealing temperature increases to from the left to the right)
4. M - GeneRuler DNA Ladder Mix #SM0333 (Fermentas)



Notes:




Isolation and digest of pKS-CRO (ligated and transformed into E. coli the previous day)





Kuba




• pKS-CRO cut with XbaI and EcoRI



• Gel (from the left)
1. GeneRuler DNA Ladder Mix #SM0333 (Fermentas)
2. uncut plasmid (isolate no.1)
3. cut plasmid (isolate no.1)
4. uncut plasmid (isolate no.2)
5. cut plasmid (isolate no.2)
6. uncut plasmid (isolate no.3)
7. cut plasmid (isolate no.3)

Note: isolate no.1 contains a correctly inserted PCR product

Cloning the p53 coding sequence

Marcin

Comment

There were some difficulties with ligation p53 coding sequence into pKS plasmid so I decided to take another sample containing isolate amplified p53 (via PCR reaction) and perform digest of the sample using XbaI

Tasks:

• Restriction digest of p53 coding sequence obtained from PCR reaction

Methods:

• Reaction mixture composition:

22.5 ul PCR product (DNA concentration about 6.5 ng/ul), 2.5 ul Tango Buffer (Fermentas), 0.5 ul XbaI (Fermentas)

• Digest program:

Digest

 3h 37 °C 
15 min 80 °C 
~4 °C 

• Quantification of the amount of DNA after digest on the agarose gel

Methods:

• Electrophoresis of the digested DNA sample:

agarose concentration - 1%

voltage - 70V

time - about 30 minutes

After electrophoresis gel was irradiated with UV light and photographed:

Gel which should contain the digested PCR product.

Comment

The sample must have degraded after gel-out procedure. Most probably due to acidic condition in the solution DNA hydrolysed. It is obligatory to do another PCR reaction using the old plasmid sample (I hope the DNA is not degraded!).

Miecznikowa team Aim: debug RFP-terminator ligation that did not work

Jarek/Franek/Ania

Task1:

• Alkaline lysis of the plasmid containing Terminator

Methods:

• PlasmidMini set by A&A Biotechnology was used. 2 test tubes with 5ml LB and 5 ul Ampicyline were first inoculated with the plasmid containing colonies. The cultures were incubated over night at 37C.Alkaline lysis was performed on both cultures. The pellet from 5 ml of bacteria was used.

Results:

• DNA extraction quality controll.DNA Concentration was measured using Spectrophotometer NanoDrop ND-1000

Task2:

• We decided to measure the concentration of DNA in our samples for future use e.g. efficient ligation mix. NanoDrop ND-1000 was used.

Results:

Notes - IMPORTANT:

• Rfptra and RBSdigested samples were extracted from the gel using gel-out kit by A&ABiotechnology. Presented data shows that after gel extraction there is very little DNA in the sample.

  Probably there is a ****problem with gel extraction procedure**** - the Gel-out set by A&A Biotechnology might be defective.

Miecznikowa team - division of labour;)

Today the intermediate bricks were designed and we divided the tasks as follows:

• Franek: BBa_J5528, digestion with (EcoRV, PstI) and insertion into pKS2 (Bluescript) cut with SmaI i PstI (look for white colonies on the X-gal, IPTG, Amp plates)
• Jarek: construct BBa_K177011
• Michał: construct BBa_K177012
• Marek: construct BBa_K77013
• Ania: construct BBa_K177014
• Monika: transform competent cells with BBa_1763004, BBa_S03473, BBa_E0840, BBa_J07037 out of the distribution.

potential problems: get inv/llo/phoP/phoQ

adjusting part pSBBBa_J5528

Franek

Task:

• transform competent cells with BBa_I0500

Methods:

• Resuspension of DNA from plate 1, 14N (BBa_I0500) with 15µl of H2O
• Transformation of chemocompetent cells with 4µl of BBa_I0500 DNA solution
• Plating bacterias on LB medium supplemented with kanamycin

Results:

• Will be determined tomorrow

Jarek

Task:

• Preparation of bacterial cultures containing parts R0010, B0032 and C0051 in LB with ampicilin

Methods:

• Concentration of ampicilin used for cultures was 100 ug/ml

Results:

• The growth of the cultures will be observed on the next day