• Home
• Team
• Project
• Parts
• Modelling
• Sponsors
• Lab Book

Project

• Overview
• Choices Rationale
• Characterisation
• Safety
• Judging Comments

Sub-projects

• Metal Intake/Efflux
• Metal Sensing
• Sporulation Tuning
• Population Dynamics
• Stochastic Switch
• Metal Sequester
• Chassis
• Promoter Library

Wet Lab

• Lab Book
• Protocols

Meetings

• Meetings Calendar

Planning

• Timeline
• Ideas

Links

• Helping other teams
• Ethics
• T-Shirts
• iGEM Meetup
• Our City
• Fun and Games
• Sponsors
• Useful Links
• Contact Us
• Press Coverage

Lab Work - 28/07/09

Introduction

In the past few lab sessions the team has transformed JM109 E. coli cells with five BioBricks from the Spring Distribution and attempted to grow the transformant cells on LB + amp plates. The five BioBricks include BBa_C0056 (cI in the lambda phage), BBa_B1002 (terminator sequence), BBa_C0077 (CinR activator), BBa_C0076 (autoinducer synthetase) and BBa_R0077 (promoter which is CinR and HSL regulated - RBS+).

It was found that when the five sets of transformant E. coli cells were plated out, the cells possessing BBa_C0056, BBa_B1002, BBa_C0076 and BBa_R0077 seemed to produce colonies (although it must be noted that there was a little uncertainty about whether the E. coli transformed with BBa_C0076 did actually produce colonies). Three colonies from each of the four transformant plates were taken and each used to inoculate tubes containing 5ml LB solution (making a total of 12 tubes). These tubes were then placed in the orbital incubator overnight for mini-preps.

Today's plan is to conduct mini-preps on the four sets of E. coli transformant cells

Practical Outline

Here's the objectives for today's lab session:

1. Carry out mini-preps of the E. coli cells which have taken up the BioBricks BBa_C0056, BBa_B1002, BBa_C0076 and BBa_R0077
2. Run these mini-prep samples on the gel to check for DNA

Observations and Hypothesis

When the 12 tubes (each with 5ml LB plus E. coli cells) were taken out of the orbital incubator it was seen that the tubes possessing JM109 cells + BBa_C0076 were clear compared to the other 'cloudy' tubes. This means that the transformant E.coli in the other tubes grew successfully but there was no E. coli growth in the tube where BBa_C0076 transformants should have been.

This means that the so-called colonies found on the LB + amp plate containing the E. coli + BBa_C0076 were not colonies at all! This means that the attempts to transform both BBa_C0077 and BBa_C0076 have failed.

After analysis of the situation, the team studied the plasmid in which the two BioBricks are found. It turns out that both BioBricks are carried by the same plasmid backbone - pSB2K3 - and that this plasmid DOES NOT CONFER AMPICILLIN RESISTANCE! The resistance it bears is kanamycin resistance - this is why the attempted transformations have not grown colonies on the plates. This error has slowed down progress but it has also taught the team some valuable lessons in organisation and lab planning.

Procedure

Mini-Preps for BBa_C0056, BBa_B1002 and BBa_R0077 transformants

The mini-preps carried out on the three sets of transformed JM109 cells was done using Phil's Mini Method protocol. There weren't any particular changes to the protocol but a suggestion was made to use the aspirator/vacuum pump when removing the supernatant in step 2 (where Solution I + RNAse is added) - this method ensures rapid removal of supernatant and also saves on waste flasks.

When using the Speed Vac machine in step 9, the Speed Vac protocol was observed to ensure the machine doesn't get damaged by incorrect handling.

Once the mini-prep procedure was completed the plasmid samples were stored in the -20C freezer for later use.

DNA Gel Electrophoresis

To show that we have DNA in our samples and that the DNA is not anything but our desired BioBricks (within their correct plasmids) we carried out DNA gel electrophoresis on our plasmids. Although we loaded the samples as the electrophoresis protocol suggests there was a change made to the preparation of the DNA samples; each of the nine samples consisted of:

• 10ul of distilled water
• 5ul of plasmid DNA (along with BioBrick)
• 2ul of loading buffer/dye

The DNA gel electrophoresis was allowed to commence for 40 minutes under 100volts. Once this time had elapsed a photograph was taken of the gel under UV light using the GelDoc system. This is the photograph: